Los rotores están soportados por cojinetes insertados en dos placas de apoyo, en donde en el extremo de cada eje del rotor hay un engran de sincronización. La rotación sincronizada entre cada rotor se transfiere luego a través del ajustador de calibración para el registro, que proporciona una medición consistente y superior de precisión.

Especificaciones

Flujo: Puede medir su flujo en ambas direcciones hasta 3,785 Litros por Minuto (1,000 GPM)
Precisión Lineal: Capaz de ± 0,15% sobre la gama del flujo completo
Repetibilidad: Capaz de 0,02% (condiciones de funcionamiento constantes con medidores 700 SP y registro mecánico, fluído de prueba 1 CPS)
Viscosidad: Medir con precisión hasta 1.500.000 SSU (325.000 CPS)
Temperatura: – 40 to 160°F (- 40 to 71°C)
Homolagaciones: Cumple con una gama amplia de requerimientos de pesos y medidas del mundo.
1368/5000
The TCS 700 Series flow meters feature a simple and very efficient measurement design consisting of a housing and three rotors that rotate synchronously inside the measurement chamber. The absence of wear, without metal-to-metal contact inside the chamber, eliminates any reduction in accuracy and provides a long life.

The rotors are supported by bearings inserted in two support plates, where at the end of each rotor shaft there is a synchronization gear. Synchronized rotation between each rotor is then transferred through the calibration adjuster for registration, which provides a consistent and superior measurement of accuracy.

Specifications

Flow: You can measure your flow in both directions up to 3,785 Liters per Minute (1,000 GPM)
Linear Accuracy: Capable of ± 0.15% over the full flow range
Repeatability: Capable of 0.02% (constant operating conditions with 700 SP meters and mechanical register, 1 CPS test fluid)
Viscosity: Accurately measure up to 1,500,000 SSU (325,000 CPS)
Temperature: – 40 to 160 ° F (- 40 to 71 ° C)
Homolagaciones: Meets a wide range of world weight and measurement requirements.
Enviar comentarios
Historial
Guardadas
Comunidad

La entrada TCS 700 Rotary Meter with Gaspar Record se publicó primero en Mako Internacional.

Los rotores están soportados por cojinetes insertados en dos placas de apoyo, en donde en el extremo de cada eje del rotor hay un engran de sincronización. La rotación sincronizada entre cada rotor se transfiere luego a través del ajustador de calibración para el registro, que proporciona una medición consistente y superior de precisión.

Especificaciones

Flujo: Puede medir su flujo en ambas direcciones hasta 3,785 Litros por Minuto (1,000 GPM)
Precisión Lineal: Capaz de ± 0,15% sobre la gama del flujo completo
Repetibilidad: Capaz de 0,02% (condiciones de funcionamiento constantes con medidores 700 SP y registro mecánico, fluído de prueba 1 CPS)
Viscosidad: Medir con precisión hasta 1.500.000 SSU (325.000 CPS)
Temperatura: – 40 to 160°F (- 40 to 71°C)
Homolagaciones: Cumple con una gama amplia de requerimientos de pesos y medidas del mundo.
1368/5000
The TCS 700 Series flow meters feature a simple and very efficient measurement design consisting of a housing and three rotors that rotate synchronously inside the measurement chamber. The absence of wear, without metal-to-metal contact inside the chamber, eliminates any reduction in accuracy and provides a long life.

The rotors are supported by bearings inserted in two support plates, where at the end of each rotor shaft there is a synchronization gear. Synchronized rotation between each rotor is then transferred through the calibration adjuster for registration, which provides a consistent and superior measurement of accuracy.

Specifications

Flow: You can measure your flow in both directions up to 3,785 Liters per Minute (1,000 GPM)
Linear Accuracy: Capable of ± 0.15% over the full flow range
Repeatability: Capable of 0.02% (constant operating conditions with 700 SP meters and mechanical register, 1 CPS test fluid)
Viscosity: Accurately measure up to 1,500,000 SSU (325,000 CPS)
Temperature: – 40 to 160 ° F (- 40 to 71 ° C)
Homolagaciones: Meets a wide range of world weight and measurement requirements.
Enviar comentarios
Historial
Guardadas
Comunidad

La entrada TCS 700 Rotative Meter se publicó primero en Mako Internacional.

682 LP – Liquefied Petroleum Gas and Ammonia

Design

The TCS 682 series flowmeter is a true positive displacement meter that incorporates an exclusive in-line design. Composed of three alternative pistons operating within their own chambers, each piston works similarly to that of an automotive vehicle engine. The pistons are mounted to an oscillation plate (crankshaft) from which an axis from the upper face and a valve pivot connected to the lower part protrude.

The valve pivot drives a sliding piston valve while a known quantity of product flows through each cylindrical orifice, so that it controls the sequence of steps in a uniform mechanical movement, said movement is transferred by the transmission shaft to the register

Specifications

▬ Flow range: 0.2 – 50 GPM (0.76 to 190 LPM); 250: 1 rate of decline
▬ Repeatability: capable of 0.01%
▬ Linear accuracy: capable of +/- 0.1% over the flow zone
▬ Operating pressure: 150 PSI (10.5 BAR, 10.5 kg / cm²)
▬ Temperature range: – 40 to 160 ° F (- 40 to 71 ° C)
▬ Connections: 1-1 / 2 “NPT standard flanges, with option of 1” & 2 “NPTl. BSPT, slide welding, and ANSI flanges available upon request.
▬ Types: SP, SPA, SPD, AF, SS, SSD, & LP Viscosity range: Accurately measures up to 50,000 SSU (11,000 CPS)
▬ Material: aluminum, ductile iron, stainless steel

La entrada TCS 682 Piston Meter with Gaspar Record se publicó primero en Mako Internacional.

682 LP – Liquefied Petroleum Gas and Ammonia

Design

The TCS 682 series flowmeter is a true positive displacement meter that incorporates an exclusive in-line design. Composed of three alternative pistons operating within their own chambers, each piston works similarly to that of an automotive vehicle engine. The pistons are mounted to an oscillation plate (crankshaft) from which an axis from the upper face and a valve pivot connected to the lower part protrude.

The valve pivot drives a sliding piston valve while a known quantity of product flows through each cylindrical orifice, so that it controls the sequence of steps in a uniform mechanical movement, said movement is transferred by the transmission shaft to the register

Specifications

▬ Flow range: 0.2 – 50 GPM (0.76 to 190 LPM); 250: 1 rate of decline
▬ Repeatability: capable of 0.01%
▬ Linear accuracy: capable of +/- 0.1% over the flow zone
▬ Operating pressure: 150 PSI (10.5 BAR, 10.5 kg / cm²)
▬ Temperature range: – 40 to 160 ° F (- 40 to 71 ° C)
▬ Connections: 1-1 / 2 “NPT standard flanges, with option of 1” & 2 “NPTl. BSPT, slide welding, and ANSI flanges available upon request.
▬ Types: SP, SPA, SPD, AF, SS, SSD, & LP Viscosity range: Accurately measures up to 50,000 SSU (11,000 CPS)
▬ Material: aluminum, ductile iron, stainless steel

La entrada TCS 682 piston meter se publicó primero en Mako Internacional.

La entrada Minimum Loss Cilinder Filling Valve se publicó primero en Mako Internacional.

La entrada Vertical inferior inlet, Seismic Valve Flanged Mod. VB-319F se publicó primero en Mako Internacional.

La entrada VERtical bottom inlet, Seismic Valve NPTA Mod. VB-316F se publicó primero en Mako Internacional.

La entrada Horizontal Seismic Valve NPTA Mod VB-319F se publicó primero en Mako Internacional.

La entrada Vertical Seismic Valve NPT VT316 se publicó primero en Mako Internacional.

La entrada Vertical Seismic Valve NPT 316 se publicó primero en Mako Internacional.